Mettler Toledo PS6L Specifications Page 38
- Page / 75
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
Chapter 4: Setup Parameters and Calibration
4-3 (08/09)
Configuring Setup
Parameters
WARNING
ONLY PERMIT QUALIFIED PERSONNEL TO SERVICE
THIS EQUIPMENT. EXERCISE CARE WHEN MAKING
CHECKS, TESTS AND ADJUSTMENTS THAT MUST BE
MADE WITH POWER ON. FAILING TO OBSERVE
THESE PRECAUTIONS CAN RESULT IN BODILY HARM.
To enter the setup mode, press and hold the UNITS key for up to eight seconds
until the message Setup is displayed. Release the UNITS key, and the first function (PB
0) will be displayed.
To program the scale, use the two function keys as follows:
Units Key - will accept the current displayed parameter value and increment to the
next function (IE: program block or Step).
Zero Key - will scroll through the available parameters for a specified function,
(IE: program block or Step).
This section describes the program blocks that govern normal operation including:
Pb 0 Push Button Zero Range*
PAr Parity –RS232
0 CurS Zero Cursor (indicator bar) * StoP Stop Bits – RS232
unitS Units displayed at Power-up * Proto Comm. Protocol –RS232
buiLd Build (Capacity/Increment)* SLEEP Sleep
ALt Alternate Units (Switching) Geo in GeoCal™ *
nodE Mode * CAL V Cal Weight used*
FiLtEr Filter CAL Calibration *
bAud Baud Rate – RS232 End End
ASCii
ASCII – RS232
* Items are locked by the Calibration Jumper W1
The PS scale can also be configured remotely through the METTLER TOLEDO Host
Interface. Details for configuring the scale using the Host Interface are given in the
Appendix at the end of this manual.
Program Menu chart
Units Key - will accept the value
and scroll vertically to the next step.
Zero key - will move horizontally to
the next parameter value.
To exit the set up program early:
First Method
o Press the UNITS key repeatedly
until End is displayed.
o Press the ZERO key until SAVE
or Abort is shown.
o Press the UNITS key to accept
Second method
Disconnect the power from the
scale. Changes will not be saved.
The 7 segment display is limited on
the Alpha characters that can be
displayed, (IE: no “m” can be
displayed so letter “n” is used
instead.
- Shipping Scales 1
- METTLER TOLEDO 2
- Publication Problem Report 3
- PRECAUTIONS 6
- CONTENTS 8
- 1 Introduction 10
- Standard Features 11
- Optional Accessories 12
- Specifications 13
- Physical Dimensions 13
- Power Requirements 14
- Environmental 14
- Requirements 14
- Standards Compliance 15
- RFI Susceptibility 15
- Chapter 1: Introduction 16
- 1-7 (08/09) 16
- FOR YOUR NOTES 17
- 2 Installation 18
- Correct Level 21
- Incorrect Level 21
- USB Connection - Preferred 22
- Location Codes 24
- Installation of 25
- Accessory Items 25
- Remote Displays 25
- Installing the Ball 28
- Transfer Platter 28
- Installing Conveyor 28
- Drop in Kit for PS90 28
- Power-up Sequence 30
- Keypad and Display 31
- The Display 31
- Keys and Navigation 31
- Operator Functions 32
- Parcel Weighing 32
- Unit Switching 32
- Zeroing the Scale 32
- Cleaning and Regular 33
- Maintenance 33
- TECHNICAL MANUAL 36
- PS Scale Program Menu 37
- Configuring Setup 38
- Parameters 38
- Push Button Zero 39
- Zero Cursor 39
- Units at Power-up 40
- Build Program Block 40
- Alternate Units 41
- Mode Program Block 42
- Filter Program Block 42
- Baud Program Block 42
- Sleep Program Block 44
- GeoCal™ Program 44
- Calibration Weight 44
- Calibration Program 45
- End Program Block 46
- Metrological Seal 47
- Installation 47
- 4-13 (08/09) 48
- 4-14 (08/09) 49
- 5 Service and Repair 50
- Error Code Section 51
- Check Wall 51
- Transformer 51
- Blank Display 52
- No Keypad Interaction 52
- Indicator Locked 52
- Serial Communication 53
- Test with PC 53
- For MT SIC Proto, also click 55
- Update Processor or 56
- Scale Software 56
- CAUTION 56
- Replace Main PCB 57
- Load Cell 58
- Replacement 58
- Replacing the Base 59
- Mount Display 59
- 5-11 (08/04) 60
- Interface 62
- Scale Status Byte 66
- Scale Confidence 66
- Byte Format 66
- Calibrate Using Host 67
- Configure Scale 68
- Parameters Using 68
- Host Interface 68
- PS30 only 69
- FOR YOUR NOTES 71
- References 72
- Hardware 72
- Electrical Connection 72
- Protocol 73
Related products and manuals for Kitchen scales Mettler Toledo PS6L
(142 pages)
Kitchen scales Mettler Toledo MT User's Guide
(129 pages)
(129 pages)
© 2020, manymanuals.com. All rights reserved. | 1.041 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals