Mettler Toledo PS6L Specifications Page 51
- Page / 75
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
METTLER TOLEDO PS Shipping Scale: Technical Manual
5-2 (08/09)
Error Code Section
Error codes are displayed on the weight indicator with a leading “E” to distinguish
themselves from weight data.
Code
Meaning Action
E1 ROM (checksum) error
Replace the circuit board to clear this error (call Mettler Toledo
Service)
E2 RAM error
Replace the circuit board to clear this error (call Mettler Toledo
Service)
E3 EEPROM error
Setup and /or calibration information does not match EEPROM
requirements. Press any display button and the scale will enter
setup mode or calibration mode depending on what information
requires updating.
If both setup and calibration information has been lost, the
scale will enter setup mode first when a display button is
pressed. After completing the setup, the scale will display E3
again until a button is pressed to enter calibration mode and
calibration is completed.
Reset the setup parameters and/or recalibrate to clear this error.
If the scale continues to display E3 after the setup and/or
calibration has been completed, the load cell is unable to save
the information and will need to replaced (call Mettler Toledo
Service)
E4 TC error
Load cell harness not properly connected, or load cell not
communicating to circuit board. Check harness connection. If
error persists, replace the load cell to clear this error (call Mettler
Toledo Service)
E5 Serial Communications (Data) error
The scale has received a character from the host with an invalid
parity. The scale will display E5 until either a display button is
pressed or another character is received. This error could be
caused by an incorrect Baud Rate or Data Bits (ASCii
parameter) selection in the scale setup. Confirm selection of the
set up parameters.
Check Wall
Transformer
For USB Communication: Does not require the power supply.
For RS232 communication: the power supply or wall transformer can be checked for
proper voltage with an electrical multi-meter by a trained technician. The center
conductor of the power supply is positive. Connect power supply to AC outlet and do
not connect to the scale. Set meter for DC voltage and check the voltage level by
inserting the positive probe in the center of the jack and the negative probe on the
outside of the jack .
Contact Mettler Toledo for
correct part number of power
adapter. Using the wrong type
of adapter may damage the
scale
- Shipping Scales 1
- METTLER TOLEDO 2
- Publication Problem Report 3
- PRECAUTIONS 6
- CONTENTS 8
- 1 Introduction 10
- Standard Features 11
- Optional Accessories 12
- Specifications 13
- Physical Dimensions 13
- Power Requirements 14
- Environmental 14
- Requirements 14
- Standards Compliance 15
- RFI Susceptibility 15
- Chapter 1: Introduction 16
- 1-7 (08/09) 16
- FOR YOUR NOTES 17
- 2 Installation 18
- Correct Level 21
- Incorrect Level 21
- USB Connection - Preferred 22
- Location Codes 24
- Installation of 25
- Accessory Items 25
- Remote Displays 25
- Installing the Ball 28
- Transfer Platter 28
- Installing Conveyor 28
- Drop in Kit for PS90 28
- Power-up Sequence 30
- Keypad and Display 31
- The Display 31
- Keys and Navigation 31
- Operator Functions 32
- Parcel Weighing 32
- Unit Switching 32
- Zeroing the Scale 32
- Cleaning and Regular 33
- Maintenance 33
- TECHNICAL MANUAL 36
- PS Scale Program Menu 37
- Configuring Setup 38
- Parameters 38
- Push Button Zero 39
- Zero Cursor 39
- Units at Power-up 40
- Build Program Block 40
- Alternate Units 41
- Mode Program Block 42
- Filter Program Block 42
- Baud Program Block 42
- Sleep Program Block 44
- GeoCal™ Program 44
- Calibration Weight 44
- Calibration Program 45
- End Program Block 46
- Metrological Seal 47
- Installation 47
- 4-13 (08/09) 48
- 4-14 (08/09) 49
- 5 Service and Repair 50
- Error Code Section 51
- Check Wall 51
- Transformer 51
- Blank Display 52
- No Keypad Interaction 52
- Indicator Locked 52
- Serial Communication 53
- Test with PC 53
- For MT SIC Proto, also click 55
- Update Processor or 56
- Scale Software 56
- CAUTION 56
- Replace Main PCB 57
- Load Cell 58
- Replacement 58
- Replacing the Base 59
- Mount Display 59
- 5-11 (08/04) 60
- Interface 62
- Scale Status Byte 66
- Scale Confidence 66
- Byte Format 66
- Calibrate Using Host 67
- Configure Scale 68
- Parameters Using 68
- Host Interface 68
- PS30 only 69
- FOR YOUR NOTES 71
- References 72
- Hardware 72
- Electrical Connection 72
- Protocol 73
Related products and manuals for Kitchen scales Mettler Toledo PS6L
(142 pages)
Kitchen scales Mettler Toledo MT User's Guide
(129 pages)
(129 pages)
© 2020, manymanuals.com. All rights reserved. | 0.522 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals